Видео

950H available

Hi, i had a problem w my planner ( same one) and what i did to help it feed was to add shim washers under the mounting caps that hold the rollers in & it is like new - The washers are .030 thick-& i ground an flat on one side to fit against the roller mounting block- works great- put a straight edge across the rollers and see how close the blade is - mine was teatering on the blade until i added the shims - now there’s about .040 gap between the straight edge and blade - I will make a video of what i did

Transmission hydraulic oil did use

I have the same model, 2" hole is max for this drill motor. I burned up the old yellow version trying a 2" bit with it.

Great video. What i found easiest to do is take metal cap off and gently push through the housing and it will slide right in. I used little amount of wd40 and then cleaned up after getting through

Nice review! Been wondering about these props.

nice

What??/?/?/ no waaaaay 😂😂😂😂

Bit won’t last long with no coolant. Those bits need a constant supply of coolant. Even just water is OK.

the engine with *ÆÅOÊÉWŒØØ* v8

hello do you think that by attaching the cables to each side of the cylinder and using it in traction it would work the same way ? thx

Boy that browser resolution says all you need to know about the age of this video.

what about for a 2003?

What a beautiful animal! Well cared for which is always good to see!

Is it easy cut wire in middle to take it out and put new one reconnect it. Any safety suggestions?

And those flat red plates are extension plates for flat fenders that go and connect to the footrest. They have no concern with ROPS. The other flat black bracket plate is for mounting tool box on ROPS.

TAFE: Tractors & Farm Equipment. Tafe makes Massey AGCO series and that ROPS is for 2600 series new generation tractors. Made in India.

I cut and spliced with high temp connections. Easy.

I am experiencing the same thing with my 2023 Wind today. And I noticed my cruise control is dodging cars on the right lane, not the front. Weird stuff happening

I've watched several vids on these drills and it seems like no-one knows how to drill a hole properly! I was taught to pump the drill in order to break and clear the chips. This also helps keep the drill and workpiece cool plus allows coolant to flow into the hole. Your drills will go much farther between sharpenings as well. I can still hear my mentors shouting at me across the shop "PUMP THE DRILL!"

I have this machine!! Doesn’t look like it is threaded properly!! Try retreading it.

Great explanation! Thanks for taking the time!

thanks for this, inspired me. We have tiny second gen civics that have no cup holders, anywhere. I am hoping to adapt this idea to our cars, fee up the manual brake handle and add cup holders.

Hi Baxsie, I’m glad I found your videos, I’m in the same boat as you were once, or van for that matter, lol. got a suspension seat in the van and definitely not getting rid of it, I even want to add a second, anyways, I already downloaded your files of the swivel seat, massive thanks, you probably understand how trivial this design is for some people. I plan on make 2, 1 for each side and I will modify the design for the passenger seat a bit more to the middle. I can also fabricate the parking brake myself if had some better images of how it looks from some different angles. And how it’s wired and hooked up, Do you have some more pictures of this? Greetings from the Netherlands, Thomas

i did somedigging yesterday with mi mini china excavator 1 ton, in some wet, sticky clay ... in sumer i tried in the same place but it was bone dry, ... can't decide which was worse.

سلام . قیمت این را۲۱۰ دلار گذاشتید ؟ درسته ؟ من ایران هستم اینجا قیمت چند برابره

The symptom of my bad ballast was the the headlight would go off but come back on if I turned the lights off and on. Finally went out completely. I think it's really helpful to remove the metal cover at the high voltage connector and then put it back on when you're finished threading it through. It holds the shielding to the plug but can easily be removed and put back if you're careful.

Thanks for the information. I just recently also picked up a Vevor annular cutter/drill. On the first day I drilled 64 5/8” holes. It took less than 1/3 of the time as using a drill press and standard drills. I’m definitely happy with mine so far.

Chevrolet and GMC trucks are quite different from each other. The bodies may be similar but the drivetrains are totally different, especially the engines.GMC made a much more heavier duty truck back then, all the way up into the 70's I believe.The later trucks I think were much more alike. What a great find and a great video!!!!I would love to see them all restored back to stock condition.

Curious about what the ballast does ? How do you know if it's bad ?

No chance you know anything about the model, manufacturer? I’m trying to repair mine & trying to see if I can find spare parts online, though no idea the brand

Audio needs work - voice too low, drill too loud.

With practice you will feel the right pressure when the teeth are cutting right. The more coolant-lube the better and go slow n steady. It bound up from the bit expanding when it gets hot.

Just by eyeball, I can see a horrifying amount of runout on that first bit in the three jaw chuck. Next time apply less pressure, use a constant stream of coolant or lubricant (I prefer a constant stream of a light cutting oil) and turn down the speed all the way for such relatively large diameter bits. The combination of excess pressure, excess speed, and insufficient coolant will burn your bits out within a dozen holes.

Straight pipe?

Upper body…🙄

That's some poor ski instructor skiing. No wonder people's skill levels Are dropping like a stone!!

sorry, but no perfect..

He is twisting the uper body.. very bad form

Great skiing, very bad camera work. You don't swing left and right with the skier to the extent that you did, stay a bit farther back and shoot in a straight line or with less back and forth. You got me dizzy, I cut it before reaching halfway.

Is it possible to ride one “seated only”? I am trying to heal a patellar tendon tear so I’m not allowed to ski or ride bike park standing. Seated is acceptable to my surgeon and PT. Thanks

😅 *promo sm*

Thanks - your part about removing the plastic piece that holds the adjustment screw helped. It was indeed the hardest part of the job... Well... Besides trying to get the protective cap off. I broke a plastic piece off each side trying to remove the dust/moisture cover. That was terrible! Maybe some silicone applied to the gasket will make re-assembly better!

😡😡😡😡 the person that designed this headlight assembly and balanced unit, belongs in prison for crimes against humanity 😂😂😂😂 This is one of those jobs you just start with taking sandpaper to all your knuckles

What's its value?

A onde compro

It is such a pain to change that ballest

that's really cool, looks like it just needs some lubricant but that's it, awesome

For the third year, THANKS AGAIN! *This year I am doing it BEFORE it got miserable outside 😃